B31 unusual noise.

Started by Janacek, 30 Oct, 2026, 17:06

Previous topic - Next topic

Janacek

My B31 has developed an odd noise.It's best described as midway between a whine and a moan from the right side.
It only seems to happen at low revs when pulling away,and disappears as speed increases.
Just changed the oil to Halfords Classic 20/50,but don't think that could cause this
I'm thinking a dry main bearing or dry camwheel bearing.
Any suggestions?

V500

Try oiling the dynamo end bearing. A squirt of oil through the little hole on the end is usually plenty for the bush.

NClark

Quote from: V500 on 30 Oct, 2026, 17:15 Try oiling the dynamo end bearing. A squirt of oil through the little hole on the end is usually plenty for the bush.

I'm thinking the same. I've heard this kind of noise from a worn dynamo on a classic car.

Nigel

idie

Primary chain to tight?

Derek996

Or insufficient clearance between the magneto pinion and the idler pinion although I don't see how this would change once set up and the magdyno clamping strap remains tight.
1948 BSA ZB32 Competition
2015 Ducati Scrambler Classic

DAVE BRADY

Hi,

Doesn't the magdyno have a fibre pinion and a pressure plate/clutch to protect the fibre wheel? If this pressure is insufficient it can slip and make such a noise.  A bit like slack fan belt on a car.

Dave.

Derek996

Yes it does. I've no idea what it would sound like but it's quite possible.
This is the setup for the fibre plate pressure.
1948 BSA ZB32 Competition
2015 Ducati Scrambler Classic

V500

Quote from: DAVE BRADY on 31 Oct, 2026, 11:11 Hi,

Doesn't the magdyno have a fibre pinion and a pressure plate/clutch to protect the fibre wheel?

As it's covered in grease and the spider bears on the fibre gearwheel it would have to slip an awful lot to be heard above the sound of the engine when pulling away.

DAVE BRADY

Hi,

It is possible so perhaps worth checking.

Dave.

DAVE BRADY

Hi,

Just found this.  It looks like the fibre pinion is held between two plates with the star washer against the outer one.

Janacek

Took the dynamo off and found it rather stiff to turn with finger and thumb.Too stiff to feel the magnetic pulses (unlike the magneto) so I'm guessing it needs new bearings.checking the internet,they are available.
It looks a straightforward job looking at my Haynes manual,providing it comes apart easily,but I am in two minds weather to tackle it myself,or send it to a specialist.
Has anyone replaced the dynamo bearings? Was it as straightforward as Haynes would have you believe?
Any comments or hints gratefully received.

cdsdorset

It is pretty straightforward.

V500

The dynamo doesn't give the "magnetic pulses" effect as it has no points.
Dynamo's are simple enough, and you might find that a good clean and lube of the bearings (one ball race and one phos bush) and it's OK.
Both bearings have an easy time, so replacement (provided they've been occasionally lubed) is unusual.

Derek996

The dynamo should be easy to turn my hand with very little resistance, and yes there are no pulses. As V500 says a good clean and lube of the bearings might be all it needs. If your dynamo is the short E3HM 45W one it will have a phosphor bronze bush at the commutator end. If it is the longer E3LM 60W one it will have a ball race at both ends. They are easy to change although the drive side one needs a bit of dismantling of the end plate.
1948 BSA ZB32 Competition
2015 Ducati Scrambler Classic

limeyrob

Dynamo rebuild (so long as the windings are OK) is a simple DIY job.  They get dried grease on the armature that fouls on the magnet.