BSA M21 clutch sleeve

Started by dusty fog, 15 Nov, 2026, 12:30

Previous topic - Next topic

dusty fog

Hello Everyone.
I'm new to this forum, I have a 1953 BSA M21 and i need to buy a new clutch sleeve, but i can't seem to get one, either they are out of stock or on long term back order with no idea when they will come back in, does anybody know where i can get one from.
the part i am looking for is in the parts book item no26 part number... 65-3873 clutch sleeve.
many thanks in advance for any advice.

limeyrob

How bad is the old one?
Your best bet is probably an autojumble if you are near any of the larger ones.
E-bay is always worth a look too.

Derek996

The 1949-58 M series parts book lists 66-3811 as the clutch sleeve for the M20/21. eBay has these listed but made in India!
1948 BSA ZB32 Competition
2015 Ducati Scrambler Classic

Ian C

Quote from: Derek996 on 16 Nov, 2026, 11:00 The 1949-58 M series parts book lists 66-3811 as the clutch sleeve for the M20/21. eBay has these listed but made in India!

66-3811 is for the single spring clutch as the AA specified, not for the 6 spring as the OP has requested.

limeyrob

I think you will get a 65-3873 on e-bay or an autojumble, but if it all turns out to be impossible then a "money no object" fix is to get a complete 4 spring clutch conversion which will give you a nicer clutch and relieve you of around £500.  My current A10 RR has a 4 spring clutch (it came with it) and its nice, light and smooth, my previous A10 and B31 had the 6 spring and they were fine but a bit rattly.  Its a fall back option.

Derek996

Quote from: Ian C on 16 Nov, 2026, 12:41
Quote from: Derek996 on 16 Nov, 2026, 11:00 The 1949-58 M series parts book lists 66-3811 as the clutch sleeve for the M20/21. eBay has these listed but made in India!

66-3811 is for the single spring clutch as the AA specified, not for the 6 spring as the OP has requested.
Ah! That explains it. I was looking at the wrong drawing.
1948 BSA ZB32 Competition
2015 Ducati Scrambler Classic

Jim S

These BSA 6 spring clutch sleeves are a source of frustration and confusion (at least for me)

65-3873 is for a B33 and perhaps an M20/M21 with a 6 spring clutch
42-3107 is for an A7 and A10 6 spring clutch.

The problem/confusion is that these two parts look very similar but the difference is the position of the taper within the body of the part. A few years ago I ordered a 65-3873 but when I started installing the clutch the axial alignment was off. I had actually received a 42-3107 part. So even the part supplier wasn't sure what part they had.

If you have a damaged part in your hand, it may be easier to try to salvage it by weld repair and blending rather than trying to find the correct part.

limeyrob

That makes sense, so is the primary chain offset different between the singles and twins? The singles are narrower so its logical.  A lot of suppliers list clutch parts as B and A series, and I suspect that's not correct for some of the parts.
I'm with you on the weld repair, its often worth a try.

Jim S

Limeyrob

Installing a 42-3107 on a B33 results in the clutch assembly moving away from the gearbox if I remember correctly. This results in chain misalignment and the scroll seal on the inner end of the sleeve doesn't position properly with the seal stator in the primary inner cover.

Jim

JulianS

The sleeve 42 3107 was introduced on the A7 A10 B31 and B33 for the 1956 season  full width hubs bikes, EA7 prefix frame numbers for the twins and EB31 prefix frame numbers for the B31/33. The cush assembly was also modified, a spacer introduced between the front of the primary chaincase and crankcase. The changes moved the primary chain line and chaincase out by about 1/8 inch. This was needed to provide clearance between the front section of the tin rear chaincase and the gearbox.

The 1954/55 swinging arm A7/10, CA7 frame number prefix also used 65 3873.

You can see the various part numbers if you look at the appropriate parts books

The Gold Stars, B32 and B34 and the M series kept the old part.

It is easy to mix up the parts

Dan_B33

Hello,
I have sourced a lot of good parts from :

https://tribsaparts.com/

He (Naukę) speaks English and is very helpful.

Good luck

Dan
Not an expert! But made it with help of this forum

dusty fog

The reason for the new sleeve is that someone years ago milled off the threaded portion so you can't screw on the clutch removal tool.
they also milled a new clutch nut to match. 

martinh10

The 65-3873 clutch sleeve is common to B31, B33, M20, M21 & M33 according to my parts lists. The part in the attached photos is a 65-3873 (I think). It's all I have left of the six-spring clutch on my B31 which has been replaced with a "Triumph-type four-spring clutch" (a previous post tells of my woes with that - possibly more to come soon).
So Mr Fog, if it looks like what you're after, send me a PM and I'll get it off to you.