BSA Owners' Club Workshop Discussions

The BSA Workshop => Singles => Topic started by: Barnsey on 08 Nov, 2026, 14:25

Title: Centre stand.
Post by: Barnsey on 08 Nov, 2026, 14:25
Does anyone know of a tall centre stand which would fit a C15 to allow for the 18" B40 back wheel currently fitted?  I was in the process of ordering a B40 stand, but it is narrower than the one on the C15.

  I did, briefly, toy with the idea of chopping both stands and welding the bits together to make a hybrid.   
Title: Re: Centre stand.
Post by: Stubaker58 on 08 Nov, 2026, 16:55
Hi
Remember the B40 had two typesvof frame, the stand from the earlier 'swan neck' frame shoukd fit a C15 I would have thought?
Title: Re: Centre stand.
Post by: Barnsey on 08 Nov, 2026, 17:13
Ahhh!  Maybe that is what I need to  look out for then! Thanks!
Title: Re: Centre stand.
Post by: Kev D on 09 Nov, 2026, 15:10
If you already have s C15 centre stand  why not just weld a bit extra on the feet ? It can always be cut off to return it to standard.
    Easier and less expensive  than chopping- up two two perfectly good stands
Title: Re: Centre stand.
Post by: Barnsey on 09 Nov, 2026, 16:49
I had thought of that already. I have a scrap of 1" square tubing which might do the job, but the problem is that the ends of the feet are rounded, so that they roll when putting the bike up on its stand.  It makes attaching a bit on a bit trickier.
Title: Re: Centre stand.
Post by: limeyrob on 09 Nov, 2026, 19:08
Can you cut some tube to a C shape and weld it over the feet?
Title: Re: Centre stand.
Post by: Barnsey on 09 Nov, 2026, 19:53
I'll see what I can get hold of. I work for a certain well know stair lift company, so I can sometimes acquire stuff.
Title: Re: Centre stand.
Post by: iansoady on 10 Nov, 2026, 10:09
I have a redundant stand that came off my Starfire framed B'Zuki. It lifted the rear wheel (18") about 2" off the deck. If it's any use, it's yours for the price of postage and a donation to Air Ambulance. I can measure it if that helps.
Title: Re: Centre stand.
Post by: Barnsey on 10 Nov, 2026, 18:50
That is very kind of you.  Let me think on that and I'll get back to you later in the week, when I am off work and can sort it out. 
Actually I have the correct 17" wheel on its way to me courtesy of Ebay, so that might fix my woes. 
I also note that the C15 and B40 have different size rear sprockets, so I will take a look and see which my bike has. 
Also the speedo takeoff is different, the C15 being over the hub and the B40 under the hub.  I always thought that the routing of the cable was very bad and now I know why. 

P.S. I am intrigued by the thought of a B'zuki.  What engine does it have? 

Title: Re: Centre stand.
Post by: iansoady on 11 Nov, 2026, 10:34
The B'Zuki has a Suzuki DRZ400 engine. This was fitted by a previous owner who made an excellent job of the mechanical side although the electrics were a bit ropy so I've redone them. He made it right hand gearchange with a crossover shaft although Triumph pattern (down for down) so I've changed that to up for down which I prefer.

The DRZ engine is quite sprightly, pushing out about 42bhp. I believe it originated in a CCM SR40. Hopefully it has enough urge to pull the Steib along once my knee has recovered enough to ride it!

This is as bought although I've done a lot to it since then.

(https://www.iansoady.org.uk/BSA/images/IMG_0269.jpg)

This is with the Steib attached:

(https://www.iansoady.org.uk/BSA/sidecar%20images/finished03.jpg)
Title: Re: Centre stand.
Post by: Barnsey on 11 Nov, 2026, 17:04
A neat Sled!  A sidecar outfit is on my to-do list, but I need to finish with the C15s first.
Title: Re: Centre stand.
Post by: idie on 12 Nov, 2026, 11:19
Quote from: Barnsey on 11 Nov, 2026, 17:04 A neat Sled!  A sidecar outfit is on my to-do list, but I need to finish with the C15s first.
lovely outfit
Title: Re: Centre stand.
Post by: iansoady on 12 Nov, 2026, 12:14
Thanks both, I'm pleased with how it's turned out. I've only had two very short test rides. The first one gave such dramatic head shake at about 5 mph I thought I was going to be chucked off. After advice I reduced front tyre pressure to 24 psi which improved it a lot. I've since fitted a Mitas block treaded tyre at a similar pressure and also added a steering damper. I live in hope these will sort it out. My last outifit was a Norton 16H with Watsonian Avon chair in the early 70s so I'm a bit rusty but hopefully long dormant muscle memory will return.

I just popped into the shed to try starting it after it's been silent for some months. It was initially reluctant but eventually burst into - somewhat noisy - life.
Title: Re: Centre stand.
Post by: Tigerfeet on 13 Nov, 2026, 18:19
 
'Also the speedo takeoff is different, the C15 being over the hub and the B40 under the hub.' 

I don't think this is a definite rule. In the Bacon book there are pictures of C15s with the speedo cable under the hub and B40s with it over the hub. 
Title: Re: Centre stand.
Post by: V500 on 13 Nov, 2026, 20:34
Probably down to what speedo drives BSA (or their supplier) had in stock.
These things were never hard and fast.
Title: Re: Centre stand.
Post by: Barnsey on 14 Nov, 2026, 07:44
Is is definitely easier to route the speedo cable if the drive is over the hub. The previous owner had trouble routing the cable and it ended up melting on the exhaust.  Mind you he left out the spacers between the engine and frame too, which didn't help.

There is a lot of irony in this.  I have a bike which cast me £2600 and has taken 3 years to get it close to ride-able. My second bike cost me £1500 and just needed a new rectifier and the spark plug tweeking.  Not as pretty but mechanically just as good.   There must be a lesson in this. 
Title: Re: Centre stand.
Post by: rhyatt on 14 Nov, 2026, 13:37
The speedo cable goes along inside the pillion footrest bit of frame , along under the engine by the 2 oil pipes , then up the front frame downtube and under and into the headlamp assembly.
Squeezing between bottom yoke and clamp cowl