BSA Owners' Club Workshop Discussions

The BSA Workshop => Twins => Topic started by: misterbit on 03 Jul, 2024, 21:41

Title: rear wheel removal - no centre stand - by the roadside
Post by: misterbit on 03 Jul, 2024, 21:41
I can use my bike scissor lift at home, but it is really heavy to carry on a rideout
I was considering a solution could be a small screw jack (like some cars have in the boot) and a plywood platform, unless someone has solved this already?
Title: Re: rear wheel removal - no centre stand - by the roadside
Post by: rhyatt on 04 Jul, 2024, 06:35
I used to lay the bike on its side in the grass.
Mind you I had no battery to spill and was careful how much fuel in the tank
Put my jacket on grass 1st
Title: Re: rear wheel removal - no centre stand - by the roadside
Post by: misterbit on 04 Jul, 2024, 15:02
I like it - basic `down to earth`  ;D method
it would be easy enough to take the battery off
Title: Re: rear wheel removal - no centre stand - by the roadside
Post by: iansoady on 04 Jul, 2024, 16:49
I always use AGM sealed type batteries anyway these days. But I'm also unlikely to be taking out back wheels by the roadside - it's hard enough in the garage. There's always a nice man with a big van to take me home......
Title: Re: rear wheel removal - no centre stand - by the roadside
Post by: V500 on 04 Jul, 2024, 17:54
Yep, Mr Samsung to the rescue.
Fixing a flat is a horrible job in the garage, but by the roadside? Thankfully those days are long gone...even moreso if there's not even a centre-stand.
Title: Re: rear wheel removal - no centre stand - by the roadside
Post by: cornishbob on 04 Jul, 2024, 18:03
the old (not sure about the new ones) xlh spoertster clymer manuals recommends if any work on the back wheel is required the bike should be laid on its side. never heard of it being done but i suppose it happened.
Title: Re: rear wheel removal - no centre stand - by the roadside
Post by: misterbit on 04 Jul, 2024, 19:38
its all very interesting, a post script would be that I never attempt a repair, I just carry spare new tubes. (especially since ripping a valve out!)
Title: Re: rear wheel removal - no centre stand - by the roadside
Post by: TTJOHN on 05 Jul, 2024, 09:45
Yes, It's alway's advisable to carry a spare tube in the tool box, as a deflation can always rib the valve out, I allways now leave the screw on the vale loose now, this acts as an early warning if the tube is creeping and usually be rectified before any damage is done.
Title: Re: rear wheel removal - no centre stand - by the roadside
Post by: misterbit on 13 Jul, 2024, 17:30
Nice one - going to loosen mine NOW ;D
Title: Re: rear wheel removal - no centre stand - by the roadside
Post by: DAVE BRADY on 13 Jul, 2024, 20:25
Hi,

Can you not fit a centre stand?

When I was younger I could lift the back of an A10 high enough so my wife could get a breeze block under it.  No, we did not carry one just in case but one just happened to be handy.

Dave.
Title: Re: rear wheel removal - no centre stand - by the roadside
Post by: misterbit on 14 Jul, 2024, 19:51
I could, but I would prefer not to, as it has high level pipes, and would spoil the lines of the bike. Maybe look into making a removable centre stand that would live under a rear rack, or even design it to double as a rack and a stand.
Title: Re: rear wheel removal - no centre stand - by the roadside
Post by: V500 on 15 Jul, 2024, 09:19
Design a good one of those and you'll be millyonair by this time next year.