Author Topic: Primary chaincase oil  (Read 6529 times)

0 Members and 3 Guests are viewing this topic.

Phil C

  • Golden Flash
  • *****
  • Posts: 1913
    • View Profile
Primary chaincase oil
« on: 16 May, 2018, 13:31:15 »
Could someone advise me what oil I should use in the primary chaincase on my 1965 B40F please?   Thanks.   Phil.

AWJDThumper

  • Empire Star
  • *****
  • Posts: 881
  • Dandy Beagle D14 C15 B40 B40WD B44 B25 B50 A10 A65
    • View Profile
Re: Primary chaincase oil
« Reply #1 on: 16 May, 2018, 14:33:51 »
It is specified as being the same as the fork oil but slightly thinner than engine oil. 10W30 would be ok but make sure it's suitable for a wet clutch engine and doesn't contain friction modifiers (moly). In more modern parlance, a JASO MA oil is ideal. A lot of people swear by ATF in the chaincase since it's also designed for wet clutches.

Dabbist

  • Blue Star
  • **
  • Posts: 90
  • thebackyardbuilder.net
    • View Profile
    • thebackyardbuilder.net
Re: Primary chaincase oil
« Reply #2 on: 16 May, 2018, 18:20:30 »
Rupert Ratio does suggest a breathing mod for B40s which results in them sharing the engine oil and primary drive oil, so one must assume that engine oil is fine.
 Thumper's right though. The oil can play havoc with the clutch. I've been through all sorts of options on trials bikes, trying to stop clutch drag. I've used both ATF and engine oil successfully. My Cub's running on a 10w40
rebuild blog at thebackyardbuilder.net

AWJDThumper

  • Empire Star
  • *****
  • Posts: 881
  • Dandy Beagle D14 C15 B40 B40WD B44 B25 B50 A10 A65
    • View Profile
Re: Primary chaincase oil
« Reply #3 on: 16 May, 2018, 20:08:21 »
The original spec for the B40 was SAE 30/40 (W/S) for the engine and SAE 20 for chaincase and forks. Using a thicker engine oil for the chaincase might increase the tendency of the clutch to slip but I don't think there's much in it.

Phil C

  • Golden Flash
  • *****
  • Posts: 1913
    • View Profile
Re: Primary chaincase oil
« Reply #4 on: 17 May, 2018, 09:09:48 »
In my shed I have the following.  Are any of them suitable for the primary chaincase?

-  Silkolene Comp 4 10w-30 synthetic ester based engine oil   MA2   JASO T903:2011

-  Castrol Power 1 Racing   10w-40  4T

-  Comma Classic 20w50  API SE CC  (This is what I have in the engine.)

Or do I need to buy something else?  Thanks in advance.   Phil.


JulianS

  • Empire Star
  • *****
  • Posts: 2637
  • A10
    • View Profile
Re: Primary chaincase oil
« Reply #5 on: 17 May, 2018, 09:41:21 »
I recently fitted an SRM 4 spring clutch to my A10. They recommended standard 10/30 or 10/40 and also recommended do not us TQF or ATF automatic transmission oil or fork oil as they contain anti friction additives which will make the clutch slip.

I used 10/40 which works fine. Have also used Morris 20/50, same as I use in the engine, and also Morris 20 and they work fine also.

ATF comes in various specifications for different vehicles and if you choose this you need to select the appropriate spec to suit or you will get slip.

Phil C

  • Golden Flash
  • *****
  • Posts: 1913
    • View Profile
Re: Primary chaincase oil
« Reply #6 on: 17 May, 2018, 11:01:49 »
Thanks Julian. So of the three I mention, which, if any, is suitable?  Or are they all suitable?   Phil.

PS A bit complicated, isn't it?

AWJDThumper

  • Empire Star
  • *****
  • Posts: 881
  • Dandy Beagle D14 C15 B40 B40WD B44 B25 B50 A10 A65
    • View Profile
Re: Primary chaincase oil
« Reply #7 on: 17 May, 2018, 11:44:43 »
The first two oil are fine since they are JASO MA rated and suitable for wet clutches. The third is a mineral oil but may be a bit viscous for the chaincase.

JulianS

  • Empire Star
  • *****
  • Posts: 2637
  • A10
    • View Profile
Re: Primary chaincase oil
« Reply #8 on: 17 May, 2018, 14:31:19 »
Phil

Its not complicated but it is easy to over think the issue.

These bikes were designed for basic back yard maintenance

The only time I have experienced oil related clutch slip on my A10 was when I used an unsuitable ATF fluid.

When I run out of 10/40 I will go back to 20/50 because it is what I use in the engine and because I have not had any problems with it, just a nice light,  progressive and non slipping clutch.

hoogerbooger

  • Royal Star
  • ***
  • Posts: 245
    • View Profile
Re: Primary chaincase oil
« Reply #9 on: 17 May, 2018, 17:55:47 »
have been watching with interest. I think I'll try 20/50 as that's what I have for the engine.

I presume it's just a case of if the the clutch doesn't pick up/slips  ...but seems to be adjusted correctly ... then try one of the others.

Mike40M

  • Royal Star
  • ***
  • Posts: 133
    • View Profile
Re: Primary chaincase oil
« Reply #10 on: 10 April, 2020, 17:34:36 »
Waking up an old thread, though most seems to be said. Looks like the unit singles can use almost anything liquid in the primary.
I uses a lot of racing 10W-50 API SM, JASO MA2, ACEA A3 synthetic in both modern and classic race bikes.
Anybody think I can't use it in my unit singles?

Pete A10

  • Royal Star
  • ***
  • Posts: 178
    • View Profile
Re: Primary chaincase oil
« Reply #11 on: 10 April, 2020, 19:04:00 »
Why not just use what BSA recommend - SAE 20. Available on line for about£12.00/litre which will be more than enough to do the forks as well. All this information is in the User Manual which you can download for free from bsaunitsingles.com

Mike40M

  • Royal Star
  • ***
  • Posts: 133
    • View Profile
Re: Primary chaincase oil
« Reply #12 on: 10 April, 2020, 22:46:51 »
Four reasons. Already using some 20 different kinds of oils. Don't want to add another one.
I prefer things I can get immediately at a local shop instead of waiting a couple of days for delivery.
For the forks I already have 5 different viscosity fork oils.
Price. I pay £3.21/litre for the oil I use in the race bikes. (Except the Manx which uses an environmentally friendly non fossil oil called R40)

DAVE BRADY

  • Golden Flash
  • *****
  • Posts: 2627
    • View Profile
Re: Primary chaincase oil
« Reply #13 on: 11 April, 2020, 07:29:12 »
Hi,

I have used ATF in '51 Flash and '68 Thunderbolt for many years and many miles. No problems.

Dave.