Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - thunderboltandlightfoot

Pages: [1] 2
1
Triples / Re: R3 choke
« on: 13 May, 2022, 19:57:18 »
Thanks for the replies lads I am starting to get some success I had to raise the new black floats a tad changed the 1/4" petrol pipe to 5/16"had it warmed up and ticking over around a thousand revs, see what she,s like in the morning chuffed I am getting somewhere with it, thanks again much appreciated.

2
Triples / Re: R3 choke
« on: 03 May, 2022, 09:18:28 »
Are they mk1/or mk2 carbs mate message me on where you purchased them thx how much of a difference do theymake were they easy to set up .?

3
Triples / Re: R3 choke
« on: 29 April, 2022, 15:52:21 »
Is the choke system /lever fixed to the left carb --is the jetting the same as the mk2

4
Triples / Re: R3 choke
« on: 28 April, 2022, 20:14:24 »
Hi both  Have not managed to get it up to running temp so thats one negative, and I have ordered new splitter box to carb cables ,interesting to know it will not run well until warm, my commando is ok with no choke so thought i would try. 150 main jets and 106 needle jet and clip on middle groove,new slides and black floats,also neoprene float shut off valves I will try again
                           thanks for your help

5
Triples / Re: R3 choke
« on: 26 April, 2022, 21:07:40 »
Hi Not had the bike for long and the choke was seized so stripped and cleaned the carbs and put back with no chokes it starts ok with a tickle of the carbs but I am having trouble getting it to tick over, it then stalls and the process is repeated time and time again and spring is here .

6
Triples / R3 choke
« on: 26 April, 2022, 08:04:15 »
Hi All , Is there an alternative to the cable choke looping back and connectimg to the lever on the left carb,have looked at handlebar mount but it looks like the left hand carb fouls on the throttle mechanism anyone have a successful system/ route TIA.

7
Triples / Re: Rocket 3
« on: 22 February, 2022, 15:56:49 »
Thanks Admin.

8
Triples / Re: Rocket 3
« on: 29 November, 2021, 20:35:43 »
Thanks Ian, Been having a look not to much on this side of the pond.

9
Triples / Rocket 3
« on: 29 November, 2021, 11:08:38 »
Hi, Having welcomed a R3 into the fold, where in uk is the best source for spares . thanks.

10
Twins / Re: Tab washer A65
« on: 06 September, 2021, 18:42:55 »
THANKS, I DO NOT KNOW IF LOCTITE EFFECTS THE TORQUE SETTINGS,WILL LOOK INTO IT .

11
Twins / Re: Tab washer A65
« on: 05 September, 2021, 21:56:43 »
Guess i will make one then .

12
Twins / Tab washer A65
« on: 03 September, 2021, 16:07:37 »
Has anyone had problems with L/washer timing pinion on the A65 ,rebuilding one at the moment and could do with a bit more o/d on the washer ,the present dimensions on the new and old one are  o/d=0.891" the nut is 0.786",which leaves an overlap of approx 0.0525" any one make their own or know of a better source?.TIA

13
Triples / Re: colour
« on: 26 August, 2021, 22:21:32 »
Not an owner yet still looking.

14
Triples / colour
« on: 15 August, 2021, 09:04:15 »
Is the blue on the mk1 an original if so anyone know the code name ? tia

15
Twins / Re: Piston rings
« on: 11 December, 2020, 20:59:46 »
Hi, Many thanks for your prompt replies Chas & Dave ( no pun intended ) I will go for the best I can afford
     thanks again.

Pages: [1] 2