Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Gtt

Pages: [1]
1
Pre War / timing cover oil pump late 20s
« on: 12 June, 2019, 17:45:18 »
Hi

I am looking at a 1927 ish oil pump set up. Like pretty much all of them, it is broken around the 4 X 1/8 holes half way down the threaded section.

My  question however pertains to the plunger. I have two one has a small check valve with ball bearing and fine spring internally, the other does not appear to have it or provision for it. The one with the check valve I have cleaned but it doesnt strike me as being overly effective. Was this check valve removed in later production? Is the check valve problematic and potentiall restricts flow? Can it be left out?

I am looking at whether the bottom of the housing can be repaired by turning up a steel sleeve to be pressed in and turned to 1/2 ID and 20 TPI 3/4 OD.

cheers

2
Pre War / Drawings
« on: 18 April, 2019, 18:12:51 »
Hello,

I am wondering if any of the BSA engineering drawings exist? Are they available ? I know the Rudge club are fortunate enough to have most of the factory drawings and have digitised which is helpful when restoring / fabricating.

Also I am looking for an electronic copy of the book of BSA 1929

thanks

3
Pre War / Re: Balancing Act
« on: 21 May, 2018, 09:54:07 »
Thanks Bevan , fingers crossed

4
Pre War / Re: Balancing Act
« on: 20 May, 2018, 14:34:09 »
Any takers on the balance factor percentages?

5
Pre War / Balancing Act
« on: 15 May, 2018, 17:00:50 »
Hi

I am wondering if there is a chart with engine balance factors for prewar engines? Particularly 500cc and 350cc Slopers

thanks

6
Pre War / Cush drive
« on: 10 May, 2018, 03:57:00 »
I believe this is an early cush drive before the single spring arrangement?


7
Pre War / Re: BSA 350cc OH sloper 1930 Cylinder base shim
« on: 31 January, 2018, 15:18:44 »
HI Hans,

I cannot help greatly with spares. There were not a lot of these made, 1600 I believe. Some items are that same for the 500 versions which were more plentiful.

How complete is your bike and what are you looking for?

regards

Greg

8
Pre War / Re: BSA 350cc OH sloper 1930 Cylinder base shim
« on: 16 January, 2018, 01:27:17 »
I have a 29 350cc sloper with high comp piston . Spacer is 1/16 inch  approx 1.67 mm thick

regards

Greg

9
Pre War / BSA 350 sloper Crank pin bearing cage
« on: 13 December, 2017, 09:47:10 »
HI

I am looking for a crank pin cage for a  1929 350 sloper . Has to suit two rows of rollers 1/4 dia by 5/16 , 24 in total
crank pin is 1 1/8, con rod big end  1 5/8.


cheers



10
Pre War / Sloper Magneto base plate
« on: 24 November, 2017, 12:14:56 »
Hello

I am missing the base plate for a 1929 BSA sloper that sits under the magdyno. I am not sure if someone has one loose they could scan on their printer and send to me and I may be able to have one made? Alternatively I might be able to figure it out if I have the material thickness

regards

Greg

12
Singles / Re: 1929 350cc sloper
« on: 22 October, 2017, 11:14:26 »
Hi Julian,

You wouldnt be able to dropbox the 1929 manuals etc? I haven't been able to find in the vintage  club library.

regards

Greg

13
Singles / Re: 1929 350cc sloper
« on: 21 October, 2017, 02:45:28 »
Thanks Julian

The upright tube under the seat is definitely different. The forks and brake lighter also. I cannot make out whether the horizontal tube has the cut out like the 500 version.

Greg

14
Singles / 1929 350cc sloper
« on: 20 October, 2017, 00:44:15 »
Hi,
I recently acquired a d series 350 cc sloper engine is quite good condition. I am interested to know if the frame is the same as the 500? The barrel and head appears a inch shorter so I am not sure if it requires the bend in the horizontal tube above the engine. I am looking for drawings of the frame if available

Any other differences of note between the 350 and 500? I understand the 350 were less common.

Cheers

Pages: [1]