Author Topic: Compression Test  (Read 250 times)

0 Members and 1 Guest are viewing this topic.

Matt.S

  • Star
  • *
  • Posts: 8
    • View Profile
Compression Test
« on: 23 July, 2017, 11:41:25 »
Hi Folks

Can anyone tell me how many psi I should expected on compression testing my 1962 C15?

Thanks
« Last Edit: 23 July, 2017, 12:06:26 by Matt.S »

om15

  • Star
  • *
  • Posts: 25
    • View Profile
Re: Compression Test
« Reply #1 on: 23 July, 2017, 12:10:41 »
My service notes give the C15 compression ration of 8:1, (the C15S is 10:1), no mention of acceptable psi measurement, however I found this on wiki

Quote
Measuring the compression pressure of an engine, with a pressure gauge connected to the spark plug opening, gives an indication of the engine's state and quality. There is, however, no formula to calculate compression ratio based on cylinder pressure.

If the nominal compression ratio of an engine is given, the pre-ignition cylinder pressure can be estimated using the following relationship:
p = p 0    CR  γ     {\displaystyle p=p_{0}\times {\text{CR}}^{\gamma }}  p=p_{0}\times {\text{CR}}^{\gamma }
where p 0      {\displaystyle p_{0}\;}  p_{0}\; is the cylinder pressure at bottom dead center which is usually at 1 atm, CR    {\displaystyle {\text{CR}}}  {\text{CR}} is the compression ratio, and γ    {\displaystyle \gamma \;}  \gamma \; is the specific heat ratio for the working fluid, which is about 1.4 for air, and 1.3 for methane-air mixture.

For example, if an engine running on gasoline has a compression ratio of 10:1, the cylinder pressure at top dead center is
p TDC   = 1  bar  10 1.4   = 25.1  bar    {\displaystyle p_{\text{TDC}}=1{\text{ bar}}\times 10^{1.4}=25.1{\text{ bar}}}  p_{\text{TDC}}=1{\text{ bar}}\times 10^{1.4}=25.1{\text{ bar}}
This figure, however, will also depend on cam (i.e. valve) timing. Generally, cylinder pressure for common automotive designs should at least equal 10 bar, or, roughly estimated in pounds per square inch (psi) as between 15 and 20 times the compression ratio, or in this case between 150 psi and 200 psi, depending on cam timing. Purpose-built racing engines, stationary engines etc. will return figures outside this range.


Matt.S

  • Star
  • *
  • Posts: 8
    • View Profile
Re: Compression Test
« Reply #2 on: 23 July, 2017, 13:01:45 »
Thanks

I seem to be getting a reading of about 100psi after kicking it over a few times, the bike pulls well in top gear and doesn't seem to smoke etc. So I guess this should be acceptable for the amount of miles I'll be doing.

STAR TWIN

  • Royal Star
  • ***
  • Posts: 129
  • A7 A10 B31 WDB40
    • View Profile
    • Strange Sheep
Re: Compression Test
« Reply #3 on: 23 July, 2017, 14:09:42 »
Simplifying... Atmospheric pressure is approx 14.7 psi. So 8:1 compression gives 14.7 x 8 = 117.6 psi. However, the inlet valve closes after bdc so you have to reduce that by a factor depending on the cam. For rule of thumb, the expected reading would be approx 90% lower. so 117.6 x 90% = 106 psi. All assuming perfect ring and valve sealing. Pretty close to what you have recorded.   

Matt.S

  • Star
  • *
  • Posts: 8
    • View Profile
Re: Compression Test
« Reply #4 on: 23 July, 2017, 15:03:04 »
Thanks.

Good news for now!