Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Jackson

Pages: [1] 2
1
Twins / Clutch Centre Nut
« on: 16 November, 2017, 16:26:28 »
I am having real problems removing the clutch centre nut on a 53 plunger A10.
Am I doing anything stupid? Iíve bent the tab washer back.
Itís not a left hand thread is it?
Adrian.

2
Twins / Re: A65 cylinder liners
« on: 13 November, 2017, 14:08:53 »
Iím looking for some for an A10 and noticed that Burton Bike Bits have some A65 liners.

3
Twins / Re: Lucas 169SA Handlebar Light Switches
« on: 11 November, 2017, 17:27:40 »
Sounds good! Iíll be doing this when the time comes. Still dismantling the engine looks l8ke a new liner at least.

4
Sidecars / Re: A bit in the side
« on: 06 November, 2017, 15:03:29 »
An absolute beauty.

5
Twins / Re: A10 Pistons
« on: 01 November, 2017, 15:47:52 »
Thatís really useful.
Thanks both of you.
It looks like itís been rebuilt fairly recently. So if thereís  no wear in the barrel and the pistons are OK Iíll reuse them with new rings.
Iím just feeling the need to check everything in the engine is OK as the front wheel wasnít and the carburettor was in a poor state.

6
Twins / A10 Pistons
« on: 01 November, 2017, 14:38:26 »
Looking around the web, the lowest compression pistons I can find for the A10 (53 plunger) are 7.25:1. I believe the correct pistons for a GF are 6.5:1.
Does anyone have any comments about the advisability of using the higher compression pistons? They are flat, the lower compression ones are dished.
Any thoughts would be valued.
Adrian

7
Twins / Re: A7 ST petrol tank - best options to flush
« on: 23 September, 2017, 18:03:44 »
It's yellow Loctite 577 for thread sealing. Just used some. Will leak test next week.

8
Twins / Re: A7 ST petrol tank - best options to flush
« on: 19 September, 2017, 22:30:38 »
Yes, these are the different strengths, but I think that there is another one for sealing rather than holding threads. I've checked the loctite site and they have, I think, purple for this purpose but I'm not sure about its petrol/ethanol resistant properties.
Adrian.

9
Twins / Re: A7 ST petrol tank - best options to flush
« on: 18 September, 2017, 21:31:15 »
I'm about to use paraffin. Recommended by a friend. It should also leak test it. I need to put taps in first though  :) I saw a recommendation for a Loctite thread sealant but can't remember where. Any suggestions?

10
Twins / Re: A10 Exhausts
« on: 20 August, 2017, 23:56:35 »
Just  bought siamese plunger A10 exhausts from Armours. They didn't have chrome and have been having problems after a fire at their suppliers. To cut a long story short, their service was exemplary. They held a stainless set for me for months until it was evident that the chrome set weren't  going to appear. I ordered the stainless pipes and they supplied them at the cost of the chrome set. I'm hoping not to exhausts for a while, but when I do they will be my first port of call.

11
Twins / Re: Plunger A10 Front Wheel
« on: 16 August, 2017, 15:26:58 »
Thanks, I've just ordered a new spindle and bearings.
I seem to have two bushes  :)
Regards,
Adrian.

12
Twins / Re: Plunger A10 Front Wheel
« on: 15 August, 2017, 22:43:30 »
Thanks very much Steve, that's as I suspected. I'm looking forward to what I find elsewhere on the bike. :( I think, to be on the safe side and as the bearings feel a bit rough, I'll  replace the bearings and get a new stainless spindle. I really don't understand how the existing setup ever worked - the bush on the RH bearing is there so the unstepped spindle can't have fitted the LH bearing unless there are two different bearing sizes!
Regards,
Adrian.

13
Twins / Plunger A10 Front Wheel
« on: 15 August, 2017, 20:16:42 »
I have just taken the wheel (what appears to be a normal 8" half width) off and there is a collection of 3 washers or spacers on the LHS, a single washer on the RHS and the spindle has no step in it.
 This looks odd to me. Were there any like this or am I looking at a bodge?
I think my safest option is to get a new spindle and bearings and replace them. Everything else looks OK.
I'd appreciate any thoughts with thanks.
Adrian

14
Twins / Re: Plunger A10 pinch bolts
« on: 11 August, 2017, 19:15:28 »
Hi,
I'll  bear that in mind thanks.  Very nice. I'd like to reach the same condition but in the meantime I'm getting it roadworthy and attaching a Steib S500 chair - but that's another story. Now to sort out the front hub.
Adrian

15
Twins / Re: Plunger A10 pinch bolts
« on: 11 August, 2017, 15:21:24 »
Hi, Thanks very much. I looked at Draganfly, but used their parts diagram, where the part is shown, but doesn't appear underneath as an option to buy. Now you've shown me where it is I've ordered two.
Regards,
Adrian

Pages: [1] 2