Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Glover

Pages: [1] 2
1
Twins / Pistons
« on: 23 August, 2022, 19:48:34 »
Hi ,has anyone got any idea where I can get a set of
+40  8.75 /1 pistons ? Seem to be rarer than hens Teath

2
Twins / Re: Frame number
« on: 03 March, 2022, 11:50:15 »
Thanks all   , a mystery frame 😀,  I must delve deeper.

3
Twins / Re: Frame number
« on: 02 March, 2022, 11:59:45 »
If it was not sent out as a complete bike would I be able to build it up with A10 engine and apply for an age related plate  ? Hears hoping 🙏

4
Twins / Frame number
« on: 02 March, 2022, 08:12:20 »
Hi , recently purchased pre unit frame No GA7 13181,Wondering what modle it came out of factory as ?

5
Twins / Re: A10 oil pump
« on: 17 October, 2020, 21:26:46 »
Yes that might explain it , 62 etched on pump and feed port
On pump has chamfer as the a65 have the anti drain bearing
Directly under the pump , nice one thanks .

6
Twins / Re: A10 oil pump
« on: 17 October, 2020, 17:36:39 »
Hi yes I'm doing the oil mods,  I dont think it's off an a10 ,
But am in the dark as what it could be off , the mid cover will not fit either,  not a65 no webbing to the third mount !

7
Twins / A10 oil pump
« on: 17 October, 2020, 13:11:41 »
Hi all , recently bought an oil pump for
A project engine , standard cases,  supposed standard
Pump , but as you can see from the photo
The third screwe hole is about 10mm away from
Pump boss , any ideas?

8
Twins / A10 specs
« on: 25 September, 2020, 09:31:15 »
How can I find engine specs , is there any good books with it  in ? What are the standard size of large journal crank big ends please .

9
Twins / Re: A10 con rods
« on: 05 September, 2020, 14:39:34 »
Little ends lined up , as you can see there is a fair discrepancy,  surely not stretched that much !

10
Twins / Re: A10 con rods
« on: 05 September, 2020, 11:20:29 »
I do not have a crank yet , bought a really good large journal
One and guess what it got lost in the post , Her    mess,
Both big end eyes are the same size , if you lay one on top of the other joint faces line up , but little end eye on the older one is 4 mm further from bigend joint 🤪🤪🤪.

11
Twins / Re: A10 con rods
« on: 04 September, 2020, 22:43:47 »
These are the Rods .

12
Twins / Re: A10 con rods
« on: 04 September, 2020, 22:07:17 »
I'm not sure how to up load photos, sorry

13
Twins / A10 con rods
« on: 04 September, 2020, 13:40:22 »
Hi all , just purchased 2 conrods of flee bay , thinking they where a pare they have the same part number,one 67 -1160 ,R3R The other 67- 1160 ,R2R  but one is 6mm longer centre than the other ? Any ideas ,thanks Nigel. :-\

14
Singles / Re: Wheel bearings
« on: 19 June, 2018, 20:40:40 »
Thanks Buddy .

15
Singles / Wheel bearings
« on: 15 June, 2018, 15:35:32 »
Hi any one know what size front wheel bearing for 6 inch conical hub b50mx ? Thanks .

Pages: [1] 2